Ring clutch with shakel for manual release.

Finishing : Zinc Plated

The HAL-2 Lifting clutches are made of an age resistance high quality steel.
They are disigned with a safety factor of x 5 the working load.
When used in conjunction with the 2- Hole anchors and cast in into the concrete there is a safety factor of at least x 3 the working load


HAL-2 product file

Ring clutch with wire cables for manual release.

Finishing : Zinc Plated

The HAL-1 Lifting clutches are made of an age resistance high quality steel.
They are disigned with a safety factor of x 5 the working load.
When used in conjunction with the 2- Hole anchers and cast in into the concrete there is a safety factor of at least x 3 the working load.
The loop is produced of zinc solid wire rope.


HAL-1 product file

Two hole flat lifting strip anchor HAF.

Material : St 52.3 (S355J2G3)

The capacity loads are axial with breakage factor of safety equal to x 3 the working load.
A rebar must be passed through the cross hole to transfer the load into the concrete. Finishing : Black (SB)
Finishing : Hot Dipped Galvanised (HDG)
Finishing : Zinc Plated (ZP), on request.


HAF product file

Material : St 52.3 (S355J2G3)

The capacity loads are axial with breakage factor of safety equal to x 3 the working load.
Dimensions and safe working loads at concrete strength of 25 N / mm2

Finishing : Black (SB)
Finishing : Hot Dipped Galvanised (HDG)
Finishing : Zinc Plated (ZP), on request.


HAS product file

Material : St 52.3 (S355J2G3)

The capacity loads are axial with breakage factor of safety equal to 3.
A rebar must be passed through the cross hole to transfer the load into the concrete.
Dimensions and safe working loads at concrete strength of 25 N / mm2

Finishing : Black (SB)
Finishing : Hot Dipped Galvanised (HDG)
Finishing : Zinc Plated (ZP), on request.


HAE product file

Material : St 52.3 (S355J2G3)

The capacity loads are axial with breakage factor of safety equal to 3.
A rebar must be passed through the cross hole to transfer the load into the concrete.
Dimensions and safe working loads at concrete strength of 25 N / mm2

Finishing : Black (SB)
Finishing : Hot Dipped Galvanised (HDG)
Finishing : Zinc Plated (ZP), on request.


HAE/1 product file

Material : St 52.3 (S355J2G3)
The capacity loads are axial with breakage factor of safety equal to 3.
A rebar must be passed through the cross hole to transfer the load into the concrete.
Dimensions and safe working loads at concrete strength of 25 N / mm2


HAE-1,25 product file

Material : St 52.3 (S355J2G3)

Finishing : anchor black the head cold dipped galvanized (CDG).
The capacity loads are axial with breakage factor of safety equal to x 3 the working load.

Finishing : Zinc Plated (ZP), on request.


HAEP product file

Material : St 52.3 (S355J2G3)

This anchor is specially designed for use with precast SANDWICH panels.
Its suspension point is close to the gravity axis, thus allowing the element to be transported and erected in an upright position.
The capacity loads are axial with breakage factor of safety equal to 3.
Dimensions and safe working loads at concrete strength of 25 N/mm2

Finishing : Black (SB)
Finishing : Hot Dipped Galvanised (HDG)
Finishing : Zinc Plated (ZP), on request.

A rebar must be passed through the cross hole to transfer the load into the concrete.


HASW product file

Material : St 52.3 (S355J2G3)

The capacity loads are axial with breakage factor of safety equal to 3.
A rebar must be passed through the cross hole to transfer the load into the concrete.
Dimensions and safe working loads at concrete strength of 15 N/mm2

Finishing : Black (SB)
Finishing : Hot Dipped Galvanised (HDG)
Finishing : Zinc Plated (ZP), on request.


HAV product file

Material : St 52.3 (S355J2G3)

The capacity loads are axial with breakage factor of safety equal to 3.
A rebar must be passed through the cross hole to transfer the load into the concrete.
Dimensions and safe working loads at concrete strength of 25 N / mm2

Finishing : Black (SB)
Finishing : Hot Dipped Galvanised (HDG)
Finishing : Zinc Plated (ZP), on request.


HAP product file

The rubber recess formers are used for all types of 2 hole anchors


HAR product file

The mounting plates are used for all types of 2 hole rubber recess formers.


HAMP product file

The holding screws are used for all types of 2 hole rubber recess formers.


HAHS product file

Material : nitril ribber , black


HARM product file

Recess former made for HAE erection Anchors.

material : plastic, only x 1 use


HARP product file